Search:

Hi again,

I think it's 1024x768 on the Amilo L6820. I searched and that's what I found at least :)

Thanks a lot! I tried to use the Intel settings from your guidelines but it worked better with VESA so I'll stick with that.

The guidelines you wrote are really really good! Great work and thanks...

Hello,

I sometimes install Lubuntu 14.04 on old hardware that I then give away to people that can't buy they own computers. So far it's been working ok.

The last week I got an old...

A bug for this exists in launchpad: https://bugs.launchpad.net/ubuntu/+source/gnome-control-center/+bug/546785

I think I have solved it. I replaced my SATA cable + removed my wlan dongle. Strange and I'm not sure it works but it has been running for some hours now.

The behavior was really strange. I dual...

Hi,

I just installed Ubuntu 10.10 on my computer and it is so slow.

I think I have managed to narrow it down to being disk access that's slow by running hdparm.


/dev/sda:
Timing cached...

I installed Ubuntu with the Swedish Eliminate Dead Keys layout as my standard layout. On my own user account I changed the keyboard layout to Swedish Dvorak. I removed the Swedish Eliminate Dead Keys...

Every time i boot up i get an annoying message that says: Network service discovery disabled

What is that and how can I fix it?

Thanks a lot, I don't think it helped though (I couldn't find any new info there).

Hi,

I started a thread when testing Lucid http://ubuntuforums.org/showthread.php?t=1435225 This thread takes of where it ended.

In Karmic I could adjust the SpeedLevel and Accel settings for my...

Did thinkfan work for you?

I installed it and started it but my fans are still loud even though my temps looks ok.



$ acpi -t
Thermal 0: ok, 37.0 degrees C

Nice! I didn't even know that was possible.

There has been a bug report in Windows on similar offset problems for some years. The solution there is to start Gimp with --no-wintab which disables...

What do you mean with touch?

Hi,

I'm still having the same issues so no, I haven't found a solution for it yet.

Ah, nice!

I can't find the device with xsetwacom anymore (since Lucid upgrade). Check out this thread: http://ubuntuforums.org/showthread.php?t=1423278

Thanks in advance!

//Ola

Since then I have run into another problem (with Lucid and Wacoms) so I'll see when I can try it. Thanks a lot for answering though!

Did you find any solution? I'm having the same problem.

Just found out about the option Accel. It can be used like this:


xsetwacom set "Wacom Graphire4 6x8" Accel 7

where you can set values between 1 and 7.

Haven't had a chance to really try it...

I'm trying to configure my Wacom tablet in Ubuntu (9.4) and it's working pretty well!

I have one issue though.

In Windows (with the Wacom drivers) I have the option to set both Mouse Speed and...

I tried to install CakePHP to my public_html directory but I couldn't get it to work so I set up a virtual domain instead...

Hi,

Is it possible to set Apache to AllowOverride All for one of my users public_html directory but not the others?

Thanks in advance!

@Iowan: I think you are correct. But...

If I had NM installed and eth0 in /etc/network/interfaces[/] the network worked fine (ping worked). The problem was that Firefox started in offline mode...

@Iowan: Thanks for replying. I tried that first but it seems like Ubuntu has a special config for NM so it doesn't manage cards that are in /etc/network/interfaces.

I finally got it working by adding HorizSync & VertRefresh to /etc/X11/xorlg.conf. (The values are for a ViewSonic VG150 TFT monitor so if anyone use another monitor find the values for that monitor...

Just found out that I must add the mode I added with xrandr --newmode .. as a valid mode as well.

That's done with:



$ xrandr --addmode default 1024x768_60.00


If I try to change to the...